Last updated November 18, 2026
ADU Builders Troubleshooting: Common Problems and How to Fix Them
A new ADU that smells musty within six months of completion almost always has the same root cause: a vapor barrier decision made during framing that the homeowner was never told about. Not a leak. Not a bad window. A sheet of plastic, or the absence of one, decided in a week nobody documented. In our experience across Spring Valley, the callbacks that hurt most aren’t the dramatic failures. They’re the quiet ones that were baked in before the drywall went up. This guide covers the five complaints we hear most after move-in, how to tell a real defect from normal material behavior, why small ADUs get undersized HVAC systems, and how to present a problem so it gets fixed under warranty instead of argued about.
Quick Answer
Most post-completion ADU problems fall into five buckets: moisture and envelope failures, HVAC undersizing, electrical tripping, plumbing pressure issues, and finish cracking from heat cycling. The first step in every case is documenting the symptom with dates and photos, then checking whether your contractor’s written guarantee covers workmanship. Workmanship defects get fixed under warranty. Material behavior and owner-caused issues usually don’t, and knowing the difference is what keeps you from getting sold a repair you don’t need.
Table of Contents
- The Five Most Common Post-Completion ADU Complaints
- Workmanship Defect or Normal Material Behavior?
- HVAC Undersizing in Small ADUs
- Moisture and Envelope Issues in Spring Valley’s Heat Cycling
- Electrical Tripping and Load Problems
- How to Document and Present a Problem to Your Contractor
- Getting It Fixed Under Warranty Without a Fight
- Common Mistakes to Avoid
The Five Most Common Post-Completion ADU Complaints
In a desert climate, the failures follow a pattern. Spring Valley’s swing between triple-digit summer afternoons and cold winter nights puts every joint, seal, and mechanical system through more thermal movement in a year than a coastal build sees in five. Here’s what surfaces first.
- Musty smell or visible moisture at baseboards, under windows, or behind furniture on exterior walls. Usually a vapor barrier or flashing detail from framing.
- The ADU never gets cool enough in July and August, or the unit runs constantly and still sits at 78 degrees. Almost always undersized HVAC for the actual square footage and ceiling height.
- Breakers tripping when the tenant runs the microwave and a space heater together. Often a load calculation that assumed a smaller appliance package than what’s actually in there.
- Low water pressure at the shower when the kitchen sink runs. Commonly a shared supply line sized for one fixture group, not two.
- Hairline cracks at drywall seams, tile grout, and exterior caulk lines. Frequently normal heat cycling, sometimes a sign of a framing or foundation issue worth checking.
The pattern matters more than any single item. If you’re seeing two or three of these together, they often trace back to the same phase of construction. On a garage conversion in particular, the original slab and wall assembly wasn’t designed for conditioned living space, and the retrofit details carry the whole load of that change. That’s covered in more depth on our Garage Conversion Contractor in Spring Valley page.
Workmanship Defect or Normal Material Behavior?
This is the question that decides whether your repair is free or billed, and it’s the one homeowners get talked out of most often. Here’s the honest split.
- Workmanship defect: Something installed wrong or left incomplete. A vapor barrier that doesn’t overlap or seal, flashing that directs water inward, a condensate line that drains uphill, a disconnect wired to the wrong breaker. These are the contractor’s responsibility under any written guarantee worth the paper it’s printed on.
- Normal material behavior: Hairline drywall cracks at seams, minor grout shrinkage, paint settling, caulk lines opening a sixteenth of an inch as the seasons turn. Annoying, not a defect. Most of it settles within 18 months.
- Owner-caused or maintenance: Clogged filters, a tenant who never runs the fan, furniture pushed against a supply vent, plants piled against the exterior. Nobody’s fault, but not covered.
The test is whether the problem traces to a decision made during construction or to time and use afterward. Moisture behind a wall is almost never normal. A hairline crack above a door frame almost always is. If a contractor tells you a musty smell is “just how new construction settles,” get a second opinion in writing. If the fix is a $600 vapor barrier correction, that’s a warranty conversation. If it’s a $6,000 re-side, you want to know exactly why before anyone touches a hammer.
HVAC Undersizing in Small ADUs: Why It Happens and What a Fix Costs
A 500-square-foot ADU should cool easily. When it doesn’t, the cause is usually one of three things: a load calculation done for the wrong ceiling height, a mini-split sized by rule of thumb instead of by Manual J, or a builder who reused a garage conversion plan without updating the mechanical for occupied living space.
Spring Valley makes this worse than it looks on paper. Attic temperatures push past 150 degrees in July, and a ducted system running through an unconditioned attic loses efficiency before the air ever reaches the room. A mini-split sized generously for the space often outperforms a ducted system that was “big enough” on square footage alone.
Diagnosis first. Ask your contractor for the load calculation they used, not just the equipment model. If they can’t produce one, that tells you something. A proper Manual J takes the window area, orientation, insulation values, and ceiling height into account. In a desert climate it also accounts for the design-day temperature, which is a number most homeowners have never been shown.
Cost of a proper fix versus a band-aid:
- Band-aid: Add a window unit or portable AC. $400 to $900, and it runs up the electric bill while fighting the original problem. Doesn’t solve duct losses or oversized solar gain.
- Proper fix on a ducted system: Sealing and re-insulating ducts in the attic, plus air balancing. Roughly $1,200 to $3,000 depending on the run length.
- Proper fix on an undersized system: Replacing equipment with correctly sized capacity. Typically $4,500 to $9,000 for a mini-split setup, less if the electrical panel is already set up for it.
If the system was undersized from day one, the equipment replacement is a construction defect, not a maintenance cost. That’s a warranty conversation, and it’s the kind of thing The Kingswell Guarantee is written to settle in plain language rather than debate. Our ADU Builders in Spring Valley team does this sizing before the slab pour, not after move-in.
Moisture and Envelope Issues in Spring Valley’s Heat Cycling
Spring Valley buildings don’t get the gradual thermal curve they design for on the coast. Days hit 105 and nights drop into the 50s. Every exterior wall expands and contracts. Every seal gets tested. Nowhere is this more visible than at the base of the wall, where the vapor barrier meets the slab.
The common envelope failures and their construction causes:
- Musty smell indoors with no visible water: Vapor barrier installed without proper overlap, or punctured during framing and never patched. The barrier exists to keep ground moisture from migrating into the wall assembly. If it’s compromised, moisture finds the path.
- Staining at the base of exterior walls: Starter flashing missing or lapped the wrong way. Water sheds down the wall and hits a seam, not the drainage plane.
- Peeling paint or caulk along the top plate: Attic ventilation blocked or undersized, pulling moisture through the ceiling assembly instead of venting it out the ridge.
- Water in the wall cavity after a rare monsoon: Window and door flashing detail. On a garage conversion, this often traces back to a garage door opening that was framed out but not properly flashed at the new infill wall.
What repair actually involves depends on how bad the moisture is. A stained baseboard and a small patch might mean removing interior finishes, re-flashing, re-sealing, and re-installing. Expect $1,500 to $4,000 for a targeted repair. If the wall cavity has been wet for months, you’re looking at a larger scope with dry-out time and potential mold remediation, which can push past $8,000. The earlier it’s caught, the smaller the bill.
Electrical Tripping and Load Problems
Breakers that trip on a new ADU aren’t a mystery once you see the load calculation. Most ADU permits are pulled with a standard appliance package assumed: refrigerator, microwave, one or two small appliances, a mini-split, and lighting. What actually goes in is often heavier. A tenant who plugs in a space heater in winter and runs a hair dryer at the same time can trip a 20-amp circuit that looked adequate on the plan.
The fix ladder, cheapest first:
- Identify the circuit that trips and what’s on it. Write it down. This alone solves half of these calls.
- Confirm the breaker and wire gauge match. Code requires specific AWG wire per breaker size. If someone swapped a breaker during the build or afterward, that’s a defect.
- Add a dedicated circuit for the heavy appliance. Typically $350 to $900 depending on panel space and run length.
- Panel upgrade if the existing panel is a Zinsco, Federal Pacific, or already near capacity. $2,000 to $4,500.
Never swap to a larger breaker to “fix” a tripping circuit. That removes the safety device and turns a nuisance into a fire risk. If your breaker is tripping regularly, get a licensed electrician to look at it. This is one where the DIY instinct has no place.
How to Document and Present a Problem to Your Contractor
Contractors respond differently to a calm, specific list than to a frustrated phone call. The ones who show up ready to fix something do it because the list makes the fix obvious. Here’s the process that works.
- Photograph the symptom with a date stamp. Wide shot, close-up, and something for scale. If it’s a smell, log the dates and times you notice it, and note weather. Musty smell worse after rain or in the morning is useful information.
- Write one sentence per problem. “Master bath exhaust vent drips on the tile in the morning.” “Main room won’t cool below 78 on days over 100 degrees.” “Microwave trips the kitchen breaker.” Vague complaints get vague responses.
- Note what you’ve already checked. Filters, breakers, visible water, thermostats. Eliminating the obvious saves a visit and signals you’re paying attention.
- Reference the written guarantee by name. If your contractor provided a guarantee at the start of the project, quote what it says. If they didn’t provide one, that’s the first thing to raise.
- Ask for a written diagnosis, not just a fix. “Can you tell me what caused this?” is a fair question, and the answer tells you whether it’s workmanship or material behavior.
- Set a timeline in writing. “Can we schedule this for next week?” gets a commitment. “Let me know when you can come out” gets silence.
Every Lodgewick project in Spring Valley wraps with a written guarantee in hand, so the conversation starts from a document instead of a memory. That single piece of paper is the difference between a warranty claim and an argument.
Getting It Fixed Under Warranty Without a Fight
The guarantee is only useful if you know what it covers. Here’s what to check on any ADU warranty, yours or one you’re reviewing before hiring.
- Is it written? Verbal promises aren’t a warranty. Ours is delivered on every project before work begins, in writing.
- What’s covered and for how long? Workmanship and material defects are separate categories. They don’t always carry the same term. The 365-Day Done Right Promise covers the work itself, and if it fails within that window, we come back and make it right at no cost.
- Exclusions. Owner-caused damage, acts of God, and maintenance failures are typically excluded. Nothing unusual, but know what you signed.
- The resolution path. Ask how disputes are handled. A guarantee that requires arbitration across the country is worthless. A written commitment to return locally is worth everything.
Our Home Addition Contractor in Spring Valley services follow the same written-guarantee structure, which means the same rules apply to your addition that apply to your ADU. If you’re looking at a project from a contractor who won’t put their guarantee in writing, that’s the answer to whether you should hire them.
Common Mistakes to Avoid
- Accepting a verbal guarantee. If it isn’t on paper, it doesn’t exist when the trailer pulls away. Ask for it before work starts and read the exclusions.
- Skipping the load calculation review. Most homeowners never see the Manual J. Ask for it. In Spring Valley’s climate, a system sized by square footage alone will struggle from day one.
- Assuming small ADU equals easy moisture control. Small units cycle through air changes faster than a full house, and vapor barriers have less square footage to fail silently. Inspect baseboards and exterior seams twice a year.
- Swapping to a bigger breaker. The 30-amp breaker exists because the wire is sized for 30 amps. Upgrading the breaker without upgrading the wire turns a nuisance into a hazard.
- Waiting until past the guarantee window to report a problem. The 365-day clock starts at substantial completion. A musty smell in month 13 is a much harder conversation than one in month 4.
- Skipping a written scope on the repair. Even a warranty repair should come with a written scope and a date. Otherwise, you’ll have the same conversation twice.
- Hiring a repair contractor for a workmanship defect. If your original builder’s guarantee covers it, going out of pocket for the fix before filing the claim can void the coverage. File first, hire second.
When to Call a Professional

Some of these problems are wait-and-see. Hairline cracks in the first year often settle. A musty smell that gets worse each week is not one to wait on. Neither is a breaker that trips more than once in a month, an HVAC system that never gets a room below 80 on a hot afternoon, or moisture staining at the base of an exterior wall.
The rule of thumb: if the symptom is getting worse, involves water, involves heat, or involves electricity, get it looked at. And if you’re considering a repair on a warranty issue, get the diagnosis in writing before work starts so you and the original contractor are working from the same document.
Lodgewick ADU Builders Spring Valley offers free estimates in Spring Valley – call (844) 780-4284 to schedule yours, and a live person will answer regardless of the hour. Bring your photos, your dates, and your guarantee. We’ll read it with you and tell you exactly what’s covered.
Frequently Asked Questions
No, a musty smell in a new ADU is almost never normal and points to a moisture problem, usually a vapor barrier or flashing detail from the framing phase. In Spring Valley, where heat cycling stresses every exterior seal, the failure surfaces faster than it would on the coast. Get it looked at before the guarantee window closes – call (844) 780-4284 for a free assessment.
Hairline cracks at drywall seams, grout joints, and paint film within the first 18 months are typically normal material behavior from thermal cycling, not a workmanship defect. Cracks wider than a quarter inch, cracks that grow, or cracks accompanied by moisture are worth a professional look. Call (844) 780-4284 and we’ll tell you which category you’re in.
HVAC undersizing or duct losses in the attic are the two most common causes in Spring Valley, and both are usually visible in the original load calculation. A proper fix costs $1,200 to $3,000 for duct sealing and balancing, or $4,500 to $9,000 for correctly sized equipment replacement. If the system was undersized from day one, that’s a warranty issue. Call (844) 780-4284 for a free estimate on the fix.
Not if the work is genuinely covered. Legitimate warranty repairs are free to the homeowner for the covered scope. What can change the number is discovering additional damage that falls outside the guarantee, and a fair contractor will show you that in writing before proceeding. Get the scope in writing first, then decide. For a free estimate, call (844) 780-4284.
Sometimes yes – if the repair involves opening exterior walls, replacing framing, or touching electrical, plumbing, or mechanical systems, most jurisdictions require a permit. Cosmetic repairs generally don’t. Spring Valley inspectors vary by scope, and asking the question up front saves a headache later. Call (844) 780-4284 and we’ll walk you through what your repair needs.
A reasonable response is a scheduled visit with a clear window, generally within one to two weeks for non-emergency items and same-week for active water intrusion. Written guarantees should say this explicitly. Our 365-Day Done Right Promise includes a free return visit if the work fails within the guarantee period, and we schedule it like any other appointment. Call (844) 780-4284 to book one.
The Bottom Line
Most ADU problems after move-in trace back to a decision made during construction – a vapor barrier detail, an HVAC sizing shortcut, a load calculation nobody checked. Knowing the difference between a workmanship defect and normal material behavior is what keeps a warranty conversation from turning into a paid repair you didn’t need. Document the symptom with dates and photos. Read your guarantee. Ask for the diagnosis in writing. And if you’re in Spring Valley and want a contractor who hands you a written price and a written guarantee before work starts, that’s exactly what we do. Call (844) 780-4284 for a free estimate.
For more on how we handle the build itself, start at our Lodgewick ADU Builders Spring Valley home page or explore the individual ADU Builders in Spring Valley and Garage Conversion Contractor in Spring Valley services.
Written by the team at Lodgewick ADU Builders Spring Valley.


